Эта страница находится в стадии разработки. Информация, показанная здесь, может время от времени быть неполной или актуальной.
Эта страница посвящена кодам ошибок, которые можно увидеть на дисплее или в логах принтера или сервера. Принадлежность кода ошибки к ПО сервера или принтера, можно определить по начальной букве "s" пред кодом, которая указывает что ошибка принадлежит к серверу.
Код ошибки состоит из 3х частей, ABC (возможен префикс "s" - сервер):
A: к какой области относится ошибка, диапазон: 0-9
B: статус ошибки error/warning, диапазон: 0-1
C: индификатор ошибки
Пр:
k001: 0 - область конфигурации принтера; 0 - ошибка; 1 - Не удается открыть конфигурационный файл
k419: 4 - область датчика филамента; 1 - предупреждение; 9 - Алгоритм восстановления экструзии отключен.
Когда в принтере или сервере возникают проблемы во время инициализации, калибровки или печати, он может отображать код для дальнейшей диагностики. Ниже расположены ссылки на дополнительную информацию для каждого кода:
-001: Unable to open config file %s
-002: Existing command '%s' not found in gcode_macro rename
-003: Choice '%s' for option '%s' in section '%s' is not a valid choice
-004: Option '%s' in section '%s' must have %d elements
-005: Include file '%s' does not exist
-006: Recursive include of config file '%s'
-007: Section '%s' is not a valid config section
-008: Option '%s' is not valid in section '%s'
-009: Printer object '%s' already created
-0010: Unknown config object '%s'
-0011: Unable to load module '%s'
-0012: gcode command %s already registered
-0013: mux command %s %s %s may have only one key (%s)
-0014: mux command %s %s %s already registered (%s)
-0015: Error loading kinematics '%s'
-0016: Error loading template '%s': %s
-0017: Error evaluating '%s': %s
-0018: A primary [display] section must be defined in printer.cfg to use auxilary displays
-0019: Section name [display display] is not valid. Please choose a different postfix.
-0020: Unable to parse option '%s' in section '%s'
-0021: Option '%s' in section '%s' must have minimum of %s
-0022: Option '%s' in section '%s' must have maximum of %s
-0023: Option '%s' in section '%s' must be above %s
-0024: Option '%s' in section '%s' must be below %s
-0025: Unable to load module '%s'
-0026: do not parse .json file, error %s
-0027: file with data not exist: %s
-102: G-Code move transform already specified
-103: Invalid speed in '%s'
-104: Unable to parse move '%s'
-105: Unknown g-code state: %s
-106: Printer not ready
-107: Invalid speed in '%s'
-108: Unable to parse move '%s'
-109: Must home X and Y axes first
-1010: homing_override and safe_z_homing cannot + be used simultaneously
-1011: virtual_sdcard get_file_list
-1012: SD write not supported
-1013: SDCARD_RESET_FILE cannot be run from the sdcard
-1014: SD busy
-1015: SD busy
-1016: Unable to open file %s
-1017: SD busy
-1018: SD busy
-1019: Must home axis first (error axis %s)
-1020: Axis %s move out of the range
-1021: error edit file %s
-1022: Unknown stepper %s
-1023: Unknown stepper %s
-1024: Can't start printing because the printer not is calibrated. Please calibrate printer
-111: PAUSE command can't be used because the printer is in PAUSE state
-112: RESUME command can't be used because the printer is not in PAUSE state
-201: axis x=%f out of range (%f - %f)
-202: axis y=%f out of range (%f - %f)
-203: axis z=%f out of range (%f - %f)
-208: Error, tool length not enough, less 35 mm
-2010: bed_mesh: malformed '%s' value: %s
-2011: Option '%s' in section bed_mesh must have a minimum of %s
-2012: Option '%s' in section bed_mesh must have a maximum of %s
-2013: Unable to parse parameter '%s'
-2014: Unable to parse parameter '%s'
-2015: Parameter '%s' must have a minimum of %d
-2016: Parameter '%s' must have a maximum of %d
-2017: Unable to parse parameter '%s'
-2018: bed_mesh: ERROR, fade_target lies outside of mesh z range min: %.4f, max: %.4f, fade_target: %.4f
-2019: bed_mesh: Mesh extends outside of the fade range, please see the fade_start and fade_end options in
-2020: Mesh Leveling: Error splitting move
-2023: bed_mesh: probe_count must be odd for round beds
-2024: bed_mesh: Unknown profile [%s]
-2027: bed_mesh: Unknown algorithm <%s>
-2028: bed_mesh: cannot exceed a probe_count of 6 when using lagrange interpolation. Configured Probe Count: %d, %d
-2029: bed_mesh: invalid probe_count option when using bicubic interpolation. Combination of 3 points on one axis with
-2030: bed_mesh: bicubic interpolation with a probe_count of less than 4 points detected. Forcing lagrange
-2031: Value for parameter 'PROFILE' must be specified
-2032: c_axis_align: improperly formatted entry for point %s
-2033: Probe virtual endstop only useful as endstop pin
-2034: Can not pullup/invert probe virtual endstop
-2035: Must home before probe
-2036: probe error: '%s'
-2037: Probe samples exceed samples_tolerance
-2040: Need at least %d probe points for %s
-2041: horizontal_move_z can't be less than probe's z_offset
-2045: auto_wcs: improperly formatted entry for point %s
-2046: a_axis_offset: improperly formatted entry for point %s
-2047: auto_wcs: improperly formatted entry for point %s
-2048: The parameter value is out of range, param=%smm max=%smm, min=0.0mm. Check params.
-2049: Large difference between two values (x1-x2 or y1-y2), maximum difference=%smm. Check the parameters.
-2050: No module named %s, error: %s
-2051: Unknown wizard variable '%s'
-2052: Unable to parse '%s' as a literal: %s
-2053: Unknown step: '%s'
-2054: Macro %s called recursively
-2055: Failure set value:%s to slider:%s
-2056: The selected item %s not in the items %s
-2057: error setting the value:%s to move the axis, the value is out of range
-2058: error moved the axis:%s, the axis not availability
-2060: The button '%s' does not exist
-2061: Failure set value to step, value out of the range[0-%s]
-2062: the key does not exist - %s, check the key
-2064: The function restore print after power lost is disabled
-2065: The module 3d is disable
-2066: The heater %s does not support the PID control
-2067: The %s module is disconnect
-2068: Active_compensation: improperly formatted entry for point %s
-2069: Compensation not exist
-2070: difference between angles for C compensations is not equal \ on 60 degree: val=%s, c_by_max_a=%s, c_by_min_a=%s
-2071: Check the passed radius or offset for the axis A. Passed radius %s, radius calculated by kinematic position %s
-211: Radius the tool=%s greater than %s mm. Wcs will be calculated from the template
-212: Tool length=%s less %s mm. Wcs will be calculated from the template
-213: A-axis offset=%s is positive
-301: Timeout on wait for '%s' response
-302: Error send cmd to mcu '%s'
-303: Multi-mcu homing not supported on multi-mcu shared axis
-304: Unable to write tmc spi '%s' register %s
-305: Pin '%s' is not a valid pin name on mcu '%s'
-306: Stepper dir pin must be on same mcu as step pin
-307: Internal error in stepcompress
-308: Internal error in stepcompress
-309: Internal error in stepcompress
-3010: Internal error in stepcompress
-3011: full_steps_per_rotation invalid in section '%s'
-3013: Can not update MCU '%s' config as it is shutdown
-3014: MCU '%s' error during config: %s
-3015: Unable to configure MCU '%s'
-3016: Failed automated reset of MCU '%s'
-3017: Too few moves available on MCU '%s'
-3018: problems with mcu indication '%s'
-3020: Internal error in MCU '%s' stepcompress
-3021: position_endstop in section '%s' must be between position_min and position_max
-3022: Unable to infer homing_positive_dir in section '%s'
-3023: Invalid homing_positive_dir / position_endstop in '%s'
-3024: Pinter rail %s shared endstop pin %s must specify the same pullup/invert settings
-3025: Must specify %s on mcu '%s'
-3026: Unknown bus name %s '%s'
-3027: %s: spi pins must be on same mcu
-3028: Pin %s must be on mcu %s
-3029: button pins must be on same mcu
-3030: %d steps per detent not supported
-3031: Duplicate canbus_uuid
-3032: Unknown canbus_uuid %s
-3033: One or more of these steppers are unknown: %s (valid steppers are: %s)
-3034: Stepper %s phase unknown
-3035: Invalid trigger_phase '%s'
-3036: Endstop for %s is not accurate enough for stepper phase adjustment
-3037: Stats not available for stepper %s
-3039: Requested temperature (%.1f) out of range (%.1f:%.1f)
-3040: Cannot load config '%s'
-3041: Heater %s already registered
-3042: Unknown heater '%s'
-3043: G-Code sensor id %s already registered
-3044: Unknown temperature sensor '%s'
-3045: Error on 'TEMPERATURE_WAIT': missing MINIMUM or MAXIMUM.
-3046: Unknown sensor '%s'
-3047: error homing_move_end '%s'
-3048: Endstop %s still triggered after retract
-3049: Homing failed due to printer shutdown
-3050: Probing failed due to printer shutdown
-3051: Probe triggered prior to movement
-3052: Homing failed due to printer shutdown
-3054: error cmd PID_CALIBRATE '%s'
-3055: pid_calibrate interrupted
-3056: Unknown stepper '%s'
-3057: Requested min speed (%.1f) is greater than max speed (%.1f)
-3058: Requested temperature (%.1f) out of range (%.1f:%.1f)
-3059: Requested min speed (%.1f) out of range (0.0 : 1.0)
-3060: Requested max speed (%.1f) out of range (0.0 : 1.0)
-3061: Unable to open temperature file '%s'
-3062: MCU temperature not supported on %s
-3063: TMC mux pins must be on the same mcu
-3064: All TMC mux instances must use identical pins
-3065: Shared TMC uarts must use the same pins
-3066: Shared TMC uarts need unique address or select_pins polarity
-3067: TMC uart rx and tx pins must be on the same mcu
-3068: Unable to read tmc uart '%s' register %s
-3069: Unable to write tmc uart '%s' register %s
-3070: TMC '%s' reports error: %s
-3071: Unknown field name '%s'
-3073: Specify either VALUE or VELOCITY
-3074: Unknown register name '%s'
-3075: tmc virtual endstop only useful as endstop
-3076: Can not pullup/invert tmc virtual pin
-3077: tmc virtual endstop requires diag pin config
-3078: Could not find config section '[%s]' required by tmc driver
-3079: TMC SPI chain must have same length
-3080: TMC SPI chain can not have duplicate position
-3081: Pin %s reserved for %s - can't reserve for %s
-3082: Alias %s mapped to %s - can't alias to %s
-3083: Invalid pin alias '%s'
-3084: pin %s is an alias for %s
-3085: pin %s is reserved for %s
-3086: Unknown pin chip name '%s'
-3087: Invalid pin description '%s'. Format is: %s[chip_name:] pin_name
-3088: pin %s used multiple times in config
-3089: Shared pin %s must have same polarity
-3090: Unknown chip name '%s'
-3091: Duplicate chip name '%s'
-3092: Lost communication with MCU '%s'
-401: Filament error on %s
-4110: Recover extrusion by flow %s
-411: The filament has run out or there is a problem with its supply at the %s
-412: The filament has run out in the %s
-413: Switch to second extruder and resume printing.
-414: All attempt to extrude failed.
-415: Recover extrusion after cooling and heating.
-416: Recover extrusion do extrude attempt %s
-417: Extruding attempt completed successfully, resuming printing.
-418: Recover extrusion by offset %s
-419: Algorithm the recover extrusion is disable.
-501: 3D module disabled, cannot set temperature for heater 'heater_bed'
-502: Extruder '%s' not connected
-601: '%s' is not a valid extruder.
-602: Active extruder does not have a stepper
-603: Unable to infer active extruder stepper
-604: Rotation distance can not be zero
-605: Extrude below minimum temp. See the 'min_extrude_temp' config option for details
-606: Extrude only move too long (%.3fmm vs %.3fmm). See the 'max_extrude_only_distance' config
-607: Move exceeds maximum extrusion (%.3fmm^2 vs %.3fmm^2). See the 'max_extrude_cross_section' config option for details
-608: Extruder not configured
-609: Extrude when no extruder present
-6010: Extruder not configured
-6011: Extruder (trapq) not configured
-6012: Heater %s not heating at expected rate
-611: Extruder not hot enough
-612: The loop cooling did not start: loop_cool_start_temp > temp_end
-701: Not a top-level dictionary
-702: Invalid request type
-703: Missing Argument [%s]
-704: Invalid Argument Type [%s]
-705: Multiple calls to send not allowed
-706: webhooks: Unable to delete socket file '%s'
-707: Path already registered to an endpoint
-708: mux endpoint %s %s %s may have only one key (%s)
-709: mux endpoint %s %s %s already registered (%s)
-7010: The value '%s' is not valid for %s
-7011: webhooks: No registered callback for path '%s'
-7012: Remote method '%s' not registered
-7013: No active connections for method '%s'
-7014: Invalid argument
-7015: Invalid argument
-801: Unknown command: %s
-802: Error in coordinate descent: %s
-803: Unknown value '%s' in enumeration '%s'
-804: Invalid output format for '%s'
-805: Extra data at end of message
-806: Unable to parse firmware constant %s: %s
-808: Unable to obtain '%s' response
-809: Command format mismatch: %s vs %s
-8010: Unknown command: %s
-8011: Unknown command: %s
-8012: Unable to extract params from: %s
-8013: Unable to encode: %s
-8015: Error during identify: %s
-8016: Firmware constant '%s' not found
-8017: Invalid CAN uuid
-8018: Unable to connect
-8020: %s Error in canbus_uuid check
-8021: Unable to connect
-8022: Unable to connect
-8023: Serial connection closed
-811: %s Unable to open CAN port: %s
-812: %s Unable to open port: %s
-813: Printer not homed
-814: Printer not homed
-816: %s Unable to open serial port: %s
-817: %s Unknown message type %d: %s
-818: %s got %s
-901: Internal error on command: '%s', error: '%s'
-902: Malformed command '%s'
-903: Internal error on command: '%s', origline '%s'
-904: printer not ready %s
-905: The value '%s' is not valid for %s
-906: cmd STATUS %s
-907: SAVE_CONFIG section '%s' option '%s' conflicts with included value
-908: Unable to parse existing config on SAVE_CONFIG
-909: Unable to write config file during SAVE_CONFIG
-9011: error load variables %s
-9012: Unable to parse existing variable file
-9013: Unable to parse '%s' as a literal
-9014: Unable to save variable
-9015: Error on '%s': unable to parse %s
-9016: Error on '%s': %s must have minimum of %s
-9017: Error on '%s': %s must have maximum of %s
-9018: Error on '%s': %s must be above %s
-9019: Error on '%s': %s must be below %s
-911: Unknown command: '%s'
-912: The macro %s does not exist
-s001: Invalid path for option [option]
-s002: Invalid API definition. Number of websocket methods must
-s003: Error Parsing Request Arguments.
-s004: Request error
-s005: Server error: [str(e)]
-s006: File is loaded, DELETE not permitted
-s007: [str(e)]
-s008: File checksum mismatch: expected [recd_cksum]
-s009: [str(e)]
-s0010: No url argument provided
-s0011: Unable to remove rule: [pattern]
-s0012: Server Running Error
-s0013: Argument conversion error: Hint:
-s0014: Error running remote method: [method_name]
-s0015: Unable to register method [method]
-s0016: Error executing 'on_exit()' for component: [name]
-s0017: Error Closing App
-s0018: Klippy Disconnect Error
-s0019: Error executing 'close()' for component: [name]
-s0020: Klippy Stream Read Error
-s0021: Error processing Klippy Host Response: [data.decode()]
-s0022: Steapp Error
-s0024: Error run watchdog
-s101: [str(e)]
-s102: Error parsing option ([option]) from
-s103: No option found ([option]) in section [[self.section]]
-s105: Section [[self.section]], option [option]
-s106: Can only modify file backed configurations
-s107: Configuration locked, cannot modify
-s108: Option not added
-s109: Failed to set option [option] in section
-s1010: Option still exists
-s1011: Failed to remove option [option] from section
-s1012: Section not added
-s1013: Failed to add section [[section]], file: [self.files[0]]
-s1014: Section still exists
-s1015: Failed to remove section [[section]]
-s1016: Unable to find section [[section]]
-s1017: Recursive include directive detected, [file_path]
-s1018: Invalid include directive: [[section]]
-s1019: No files matching include directive
-s1020: Duplicate section [[section]] in file
-s1021: Duplicate option [option] in section
-s1022: Configuration File Not Found: [file_path]
-s1023: SteApp does not have Read/Write permission for
-s1024: Error Reading Config: [file_path]
-s1025: Configuration File Not Found: [start_path]
-s1026: SteApp does not have Read/Write permission for
-s1027: No section [server] in config
-s1028: Unable to load component: [component_name]
-s1029: Component ([component_name]) not found
-s1030: No connection associated with subscription request
-s1031: Jinja 2 environment already contains global [name]
-s1032: Error creating template from source: [source]
-s1033: Error creating template from source: [source]
-s1034: Cannot render async templates with the render() method
-s1035: Error rending Jinja2 Template
-s1036: Error rending Jinja2 Template
-s1037: Config Error: Section [[self.section]], Option
-s1038: Config Error: Section [[self.section]], Option
-s1039: Config Error: Section [[self.section]], Option
-s1040: Config Error: Section [[self.section]], Option
-s1041: The path ([config]) to config file not exist.
-s201: No data for argument: [key]
-s202: Unable to convert argument [[key]] to [dtype]:
-s203: No data for argument: [key]
-s204: failure send klippy request
-s205: failure send klippy request
-s206: Invalid Request Method
-s207: Invalid Request Params
-s208: Invalid Request Method
-s209: Invalid Request Method
-s2010: Invalid Request Method
-s2011: Invalid Request Method
-s2012: Changing to unknown network mode
-s2013: [self.transport] data not json: [data]
-s2014: JSON-RPC Request Error: [code] [msg]
-s2015: Websocket Command Error
-s2016: Error sending data over websocket: [self.uid]
-s2017: error on connect to wi-fi : [result['message']]
-s2018: system_bus is None
-s2019: Failed to detect NetworkManager service: [e]
-s2020: The device [request_device] not exist
-s2021: The device [request_device] not supported
-s2022: error get wifi points: [e]
-s2023: error get name wifi: [e]
-s2024: wlan device is not active
-s2025: SSID [ssid] not found among saved connections
-s2026: Failed to delete connection: [e]
-s2027: Unexpected error on connect to wifi
-s2028: SSID [ssid] not found among saved connections
-s2029: network manager service is not active
-s211: Error while getting ip address
-s212: Error while connecting to network: %s
-s213: %s does not match expected service: %s
-s214: Error while getting mac address
-s215: the device is None
-s301: Server can't get issues in Yandex Tracker, error: [e].
-s302: Server can't create issue in Yandex Tracker, error: [e].
-s303: Couldn't upload image to cloud: [e].
-s304: Couldn't get a download URL. [e]
-s305: Error Processing Download, Error: [e]
-s306: Retries exceeded for Stereotech API request: [url]
-s307: Password file [pw_file] does not exist
-s308: Dict or List is not json encodable
-s309: Duplicate Cloud Request
-s3010: Failed to get file: [e]
-s3011: Bad request, not set path to file.
-s3012: File not exist!
-s3013: encode error [e]
-s3014: Error message when sending to YandexTracker, problem: [e]
-s3015: printer will not download the update because its state is [self.update_state]
-s3016: not found the file: [path]
-s3019: error run the method play_sound, error: [e]
-s311: error load the object [e]
-s312: Stereotech Cloud Reconnect error: [type(e)]:[e]
-s401: Error inserting record for key
-s402: Failed to open lmdb database, aborting conversion
-s403: Namespace [namespace] already registered
-s404: Namespace [namespace] not found
-s405: Table [table_def.name] already registered
-s406: Cannot backup when Klipper is printing
-s407: Invalid name [db_name].
-s408: Invalid name [db_name].
-s409: Backup file [db_name] does not exist
-s4010: Invalid request type
-s4011: Cannot restore when Klipper is printing
-s4012: Invalid name [db_name].
-s4013: Read/Write access to namespace [namespace] is forbidden
-s4014: Value for argument 'key' is an invalid type:
-s4015: Write access to namespace [namespace] is forbidden
-s4016: Value for argument 'key' is an invalid type:
-s4017: Invalid request type [action]
-s4018: Table name [table] does not exist
-s4019: Table name [table] does not exist
-s4020: Keys in value to insert do not match columns of tables
-s4021: Keys in value to update are not a subset of available columns
-s4022: No row with id [row_id] to update
-s4023: Key [key] in namespace [namespace] not found
-s4024: Namespace [namespace] not found
-s4025: Cannot iterate a namespace asynchronously
-s4026: Item at key [rpt_key] in namespace [namespace]is
-s4027: Key [key] in namespace [namespace] not found
-s4028: Item at key [rpt_key] in namespace [namespace]is
-s4029: Key [key] in namespace [namespace] not found
-s4030: Key [key] in namespace [namespace] not found
-s4031: Table registration must occur during during init.
-s4032: Cannot register table [table_def.name], it is reserved
-s4033: Cannot compact restored database, awaiting restart
-s4034: Cannot backup restored database, awaiting restart
-s4035: Database already restored
-s4036: Restoration File [restore_path] does not exist
-s4037: Invalid database for restoration, missing table [NAMESPACE_TABLE]
-s4038: Cannot call method [func_name] while
-s501: Invalid Request Method
-s502: Invalid notification id: [nf_id]
-s503: Invalid order value: [order]
-s504: Invalid Request Method
-s505: Error while loading printjob
-s506: Invalid job id: [job_id]
-s507: Invalid Request Method
-s508: Invalid job id: [job_id]
-s509: Invalid job id: [job_id]
-s5010: Invalid job id: [job_id]
-s5011: Invalid Request Method
-s5012: Error Processing Download
-s5013: Invalid order value: [order]
-s5014: Error while loading printjob
-s5015: failed parse the job data, job ID=[job['id']]
-s5110: failure the calculating printer productivity: [e]
-s511: Server do not reconnected to klippy,status for current job the 'klippy_disconnect'.
-s5111: failure the calculating printer availability: [e]
-s512: start_time is None, job ID=[job['id']]
-s5112: metadata not available, job ID=[job['id']]
-s513: end_time is None, job ID=[job['id']]
-s5113: estimated_time not available, job ID=[job['id']]
-s514: filament_used params has negative value, job ID=[job['id']]
-s515: the [param] in job: [self.id], status=[status] is empty
-s516: the job [id] status is 'printing' after reboot services, be set 'klippy_shutdown
-s517: do not get working_days_printer, error: [e]
-s518: unable to get slice_jobs, error: [e]
-s519: failure the calculating print quality: [e]
-s601: Error Processing Download
-s602: Retries exceeded for Stereotech API request: [url]
-s603: Error Processing Download
-s604: Option 'config_path' is not a valid directory
-s605: Option 'log_path' is not a valid directory
-s606: Metadata not available for <[requested_file]>
-s607: error make directory [str(e)]
-s608: Cannot delete root directory
-s609: Directory does not exist ([directory])
-s6010: Operation Not Supported
-s6011: error remove dir: [str(e)]
-s6012: File currently in use
-s6013: File currently in use
-s6014: Invalid path: [request_path]
-s6015: Invalid root path ([root])
-s6016: Invalid path request, [request_path] is outside
-s6017: Destination path is read-only: [dest_root]
-s6018: File [source_path] does not exist
-s6019: Source path is read-only, cannot move: [source_root]
-s6020: error copy_move_file: [str(e)]
-s6021: Directory does not exist [[path]]
-s6022: Invalid root request: [root]
-s6023: No file name specified in upload form
-s6024: Root [root] not available
-s6025: Cannot write to path: [dest_path]
-s6026: File is loaded, upload not permitted
-s6027: Error uploaded file
-s6028: Failed to build file list, invalid path: [root]: [path]
-s6029: Invalid Directory Request: [directory]
-s6030: Directory does not exist ([dir_path])
-s6031: Path not available for DELETE: [path]
-s6032: Path not available for DELETE: [path]
-s6033: Delete request on file outside of root: [path]
-s6034: Invalid file path: [path]
-s6035: delete file error [e]
-s6036: Invalid metadata response: [result]
-s6037: Unable to extract metadata
-s6038: Can't parse settings params. Error [e]
-s6039: Error adding watch, already exists: [dir_path]
-s6040: Error removing watch: [node.get_path()]
-s6041: Error retrieving path info for file [file_path]
-s6042: Error running extract_metadata.py
-s6043: failed get changelog to [branch], no internet connection.Error: [e]
-s6044: No such file or directory: [source]
-s6045: failure unpack update file
-s6046: Error, incorrect format of the printer model: [model]
-s6047: error, incorrect format of the printer version: [printer_v]
-s6048: failure run the install update, error: [e]
-s6049: failure run the install update, execute code=[ex_code]
-s6050: The Extension new file ([dest_path]) name is not match [source_path].
-s611: Invalid data response: [result]
-s701: Failure check Token file not exist
-s702: Failure decode Token
-s703: Invalid JWT header
-s704: JWT Token mismatch: serial
-s705: JWT Token mismatch: manufacturer
-s706: JWT Token mismatch: type_mcu
-s707: Error create private key
-s708: The module doesn't connected
-s709: verification module failed
-s7010: verification module failed
-s801: Unsupported machine request
-s802: Service action [action] not available for steapp
-s803: Service [name] not installed
-s804: Service [name] not allowed
-s805: Error running cmd [cmd]
-s901: Invalid Request Method
-s902: Error running shell command: [self.command]
-s903: shell_command: Command [[self.name]] failed
-s904: Failed to get image from buffer! Error: [e]
-s905: Retries exceeded for Stereotech API request: [url]
-s906: Error Processing Download, Error: [e]